Join Date: Jul 2012
Location: Thunder Bay, Ontario
Posts: 47
|
|
LinkBack | Thread Tools | Display Modes |
Plastic Molding
How can I remove scuffs in the plastic mouldings inside the truck? Has anyone used the Mr. Clean Magic Erasers with any success, or are they there for good?
I can clean the dirt off, but the scuff remains.
Any ideas?
I can clean the dirt off, but the scuff remains.
Any ideas?
| Sponsored Links | |||
|
Advertisement
|
|
||
Join Date: Feb 2012
Location: Mount Forest
Posts: 633
any pic's, are they on the surface scuffs, or into the plastic scuffs ???
you can also try wd-40 with some elbow grease and scrub pad !!
you can also try wd-40 with some elbow grease and scrub pad !!
2012 XLT F150 (Sterling Grey)Tonneau Cover, 15% Tint, 6" Rough Country Lift, 18" Helo 6 Wheels(chrome), 35" Toyo Open Country A/T's, SuperChip, Rear Wheel well Liners, Hood Shield,
Window Visors, Fender Flares
Join Date: Aug 2007
Location: Woodstock, Ont
Posts: 3,353
If its a small scratch. ? (pics)
I might try a heat gun to heat it up a bit to reflow the plastic. Not too much or you will burn it. It might get really shinny and discolor.
May need a combination of superfine sand paper to semi smooth it out and then heat gun to reflow to really smoothen it.
Sent from my iPhone using Tapatalk
I might try a heat gun to heat it up a bit to reflow the plastic. Not too much or you will burn it. It might get really shinny and discolor.
May need a combination of superfine sand paper to semi smooth it out and then heat gun to reflow to really smoothen it.
Sent from my iPhone using Tapatalk
|
|
|
Join Date: Jul 2012
Location: Thunder Bay, Ontario
Posts: 47
Unfortunately, I cannot find the elusive "yellow mountain", and cannot post pictures yet. Very frustrating.
I'll try the scrubber and some WD40 or other cleaner in an inconspicuous place. These are not deep gouges, so I may be ok.
I'll try the scrubber and some WD40 or other cleaner in an inconspicuous place. These are not deep gouges, so I may be ok.
Join Date: Aug 2010
Location: F150
Posts: 4,742
Quote:
Originally Posted by hyperhad
View Post
Unfortunately, I cannot find the elusive "yellow mountain", and cannot post pictures yet. Very frustrating.
Join Date: Feb 2008
Location: Wallacetown
Posts: 2,701
Quote:
Originally Posted by SVT4MT
View Post
Load them into your fordtough.ca album with your others and someone will make sure they get posted.
Lumberjack
2010 F150 Supercrew 4X4
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
|
Show Printable Version Show Printable Version
Email this Page Email this Page
|
|
| Display Modes | |
|
|
| Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| LINEX/RHINO or Plastic bed liner | crusher | Exterior | 19 | 09-08-2010 07:56 PM |
| Fender molding | oilman | Excursion, Expedition, Navigator, Bronco, Explorer, Escape, Flex, Edge | 4 | 04-22-2010 12:03 PM |
| Faded Plastic | fordtough.ca | Care & Detailing | 1 | 07-11-2008 02:49 PM |
| wax in grey plastic...how do i get it out?? | lightning25 | Care & Detailing | 4 | 11-26-2007 07:56 PM |
| Posting Rules | |
